Based on their operating principles, they can be classified as voltage switching, voltage limiting, and combination types. (1) Voltage switching surge protective device. They exhibit high impedance in
If the distance between the incoming line terminal's surge protective device and the protected equipment is greater than 30m, a second surge protector with a current capacity of 8kA should be installe
If the combined voltage of the incoming SPD's Up voltage plus the induced voltage across its leads, as well as the reflected wave effect, is too high compared to the impulse withstand voltage of the r
The voltage protection level Up of the surge protective device device should always be less than the impulse withstand voltage Uchoc of the protected equipment and greater than the maximum operating g
Voltage-limiting type surge protective device: Its operating principle is to provide high impedance when there is no transient overvoltage. However, as surge current and voltage increase, its impedanc
To protect the protected equipment from overvoltage, the voltage protection level Up of the surge protective device must always be less than the impulse withstand voltage Uchoc of the protected equipm
Impulse Current Iimp: Specified as including the amplitude current Ipeak and charge Q. Nominal Discharge Current In: The peak current flowing through the surge protective device, 8/20μs current wave.
The type and structure of surge protective device vary according to different uses, but surge protector should contain at least one nonlinear voltage limiting element. The basic components used for su
surge protective device are essential devices for lightning protection of electronic equipment. They were formerly known as lightning arresters or surge protectors (SPDs). Their function is to limit t
Switching Type surge protective device Its operating principle is that it exhibits high impedance when there is no transient overvoltage. However, in response to a lightning transient overvoltage, its
Surge protection devices (SPDs), often referred to as "lightning arresters" or "overvoltage protectors," are essential for lightning protection of electronic equipment. The function of an surge protec
With the rapid development of electronic technology and the widespread use of personal computers, large and medium-sized computers, and related information equipment, building protection against light
1. Detection Equipment and Operational Issues Equipment Errors and Calibration Deficiencies Prolonged use surge protective device or improper maintenance leads to performance degradation of detectio
Installation Method for surge protective device: A "V" connection is recommended. The residual voltage at both ends of surge protector is ULPE = U1 + Up. The shorter connecting wires significantly red
Spacing and Energy Matching Issues When installing a surge protective device (SPD), consider the energy matching between the two stages. Generally, when SPDs are installed at multiple locations on a l
At the junction of LPZ1 and LPZ2, at the distribution panel or before the UPS, a second-level surge protective device should be installed. Products that have passed T1 or T2 classification tests shoul
Installation Location According to IEC 131221 (LPZ) concepts, surge protective device should be installed when electrical lines cross the boundary between two lightning protection zones. Depending on
Residual voltage Ures of surge protective device This is the actual voltage applied to the terminals of the protected equipment. The lower the residual voltage, the better. It should be less than the
Protection Level Up This value should be greater than the maximum limiting voltage measured at the SPD terminals and consistent with the device's withstand voltage (Uw) (1.2U p ≤ Uw). It can be select
surge protective device (SPD) Maximum Continuous Operating Voltage Uc The maximum RMS voltage or DC voltage that may be continuously applied across the SPD is equal to the rated voltage of the SPD its
Voltage-Limiting Type surge protective device (SPD) Common nonlinear components include zinc oxide varistors and transient suppressor diodes. These are widely used overvoltage protectors and are gener
Principle Power supply surge protective device comes in two types: explosion-proof box and module. Both utilize a varistor with excellent nonlinear characteristics. Under normal circumstances, surge p
Function Power supply surge protective device is typically connected in parallel to the circuit system. When lightning strikes, high-intensity electromagnetic induction is generated in various metal p
Power supply surge protective device is suitable for AC 50/60 Hz, while power supply surge protector has a rated operating voltage of 220V/380V, including TT, TN-S, TN-C, and IT power supply systems,
We use cookies to collect information about how you use this site. We use this information to make the website work as well as possible and improve our services.